Introduction
A gas turbine is, at heart, an air machine: it swallows an enormous volume of air every minute, and everything in that air — dust, salt, moisture, industrial pollutants — ends up inside the most expensive machine on the site. The only thing standing between the air and the machine is the intake filtration system, and that is why gas turbine intake filters are not a consumable. They are the turbine's first line of defence, and the cheapest insurance a plant can buy. This guide explains what intake filters do, how the stages work together, what goes wrong when they are neglected, and how to specify replacements that actually match the original.
Intake vs inlet: the same system, two words
Engineers use "intake" and "inlet" for the same system, and the two words appear interchangeably in specifications, manuals and search queries. A gas turbine inlet filter and a gas turbine intake filter are the same thing: the filtration train that sits in the filter house upstream of the compressor. What matters is the stage, not the word: within the intake there are pre-filters, coalescers and high-efficiency final filters, each doing a job the others cannot do. When a specification says "intake filter" without naming the stage, the first question should always be: which stage, at what airflow.
What the intake filter is protecting against
The first enemy is dust. Airborne dust that passes the intake deposits on compressor blades as fouling: fouled blades lose aerodynamic efficiency, the compressor works harder for the same pressure, and output falls. The loss is gradual, but it accumulates — and the recovery is a compressor wash that costs time and money. Filtration that keeps dust out stretches the interval between washes and holds output where it should be. Our guide to gas turbine compressor fouling explains the mechanism in detail.
The second enemy is salt. In coastal and offshore locations, the air carries salt aerosol that passes through coarse filtration and deposits on blades, where it drives corrosion — including the hot corrosion that attacks turbine materials at high temperature. Salt is far more damaging than the same mass of dust, which is why coastal intakes need coalescer stages that dust-only sites can do without.
The third enemy is moisture. Water in the intake carries dissolved contaminants into the machine, wets filter media and reduces its strength, and in cold conditions can form ice on the intake. Moisture also makes dust stickier, so a wet filter loads faster and a wet compressor fouls faster. The intake must handle water as a contaminant in its own right.
The fourth enemy is the intake itself: a leaking seal, a corroded housing or a poorly fitted filter bypasses the finest filtration ever made. Inspection of the intake house matters as much as the grade of the filters inside it.
The stages of a turbine intake filtration system
A turbine intake is a train of stages, each doing a job the next stage cannot do alone.
Stage | Filter type | What it removes |
|---|---|---|
First stage | Panel, pre-pocket | Coarse dust, large particles |
Second stage | Coalescer panel | Water droplets, salt aerosol |
Final stage | High-efficiency pocket | Fine dust, remaining salt |
The first stage is the sacrificial one. Industrial panel filters and pre-pocket filters catch the coarse dust and take the bulk of the loading. They are changed often, and they are what lets the expensive filters behind them live a full life. A first stage that is skipped or left in place too long passes its load downstream, and the final filters pay for it.
The second stage is the coalescer. Coalescer panel filters capture fine water droplets and salt aerosol, merging them into larger drops that drain away rather than passing through. In dry inland locations the coalescer stage carries a light load; in coastal and offshore locations it is the most important stage in the train, and its condition decides whether salt reaches the compressor at all.
The final stage is the high-efficiency pocket filter. High-efficiency pocket filters capture the fine dust and remaining salt that the earlier stages missed, and they are the last barrier before the compressor. They are the most expensive filters in the train and the most sensitive to the stages in front of them: protected by a working pre-filter and coalescer, a final filter can last a full year or more; unprotected, it can load in months.
Coastal and offshore conditions
Coastal and offshore turbines face the hardest intake conditions in the industry: salt aerosol, high humidity, rain and, in some locations, sand and industrial pollutants together. The coalescer stage must drain properly — a coalescer that cannot drain will re-entrain salt and moisture into the final filter and the compressor, which is worse than having no coalescer at all. Drains should be inspected at every outage, and coalescers should be changed ahead of the wet season rather than during it.
Salt also attacks the intake house itself: corrosion at the sealing faces, doors and drains creates bypass paths no filter can compensate for. Inspect the house as often as the filters, and repair any corrosion that distorts a sealing face before the next set is fitted.
Pressure drop and change-out timing
Pressure drop across the intake is monitored continuously on most turbines, and the final pressure drop is a hard limit, not a guideline. As the filters load, inlet pressure falls, output falls with it, and the compressor works harder. A filter changed late costs megawatts. A filter changed on time costs a filter.
The change-out schedule should be built on pressure-drop readings, with calendar intervals as a backstop. As a starting point, pre-filters are changed every 3 to 6 months, coalescers every 6 to 12 months, and high-efficiency final filters every 12 months — but the site's own conditions decide the real intervals, so run one full cycle and log the readings. A dusty site, a coastal site or a machine that runs continuously will shorten all three. Set the intervals from what the data shows. And plan around the lead time: four weeks is standard for made-to-order industrial filters, so a change-out delayed because the filters are on order is a change-out that should have been planned.
Change-outs should be done at an outage or a planned stop, with the intake isolated so filters are not changed under suction. Inspect the housing while it is empty — clean the tracks, check the gaskets and seals, look for corrosion or damage, and check that drains are clear — then fit each filter the right way round, check the seal, and record the date and the pressure drop reading.
OEM-equivalent matching for turbine intakes
When a turbine filter is replaced, the replacement should be an exact equivalent of the original: same dimensions, same efficiency class, same media behaviour. A filter that is a few millimetres out will not seal, and a filter of the wrong class will not protect. Airguard supplies Altair equivalent filters and other OEM-equivalent replacements, matched to the original part numbers so the intake performs as designed. The same discipline applies to the whole intake train: a pre-filter that does not fit the housing is a bypass path, whatever its grade.
Matching matters most at the final stage, where the efficiency class decides what reaches the compressor, and at the coalescer stage, where the media decides whether salt is captured or passed through. A supplier that claims equivalence without stating the dimensions, the class and the media has not matched anything. Ask for the match in writing, with the original part number and the proposed equivalent stated together, and keep that record on file. The OEM Part Number Guide cross-references Airguard products to the original part numbers they replace, which is the fastest way to start a match — and the guide to the individual gas turbine air intake filter covers the same ground for the US market in more detail.
For EPC and plant teams, the practical rule is simple: an equivalent is an engineered replacement, not a commodity swap. Parker / Altair equivalent Filters should be evaluated against the intake system — airflow, pressure drop, efficiency, media, sealing and environment — not just against the old part number.
Signs the intake filtration is failing
Most intake filtration failures announce themselves indirectly, and the signs are worth knowing:
output falls gradually and the interval between compressor washes shortens
pressure drop across the intake rises faster than the schedule expects
dust or salt deposits are visible downstream of the filter bank
the final filters load far faster than the pre-filters, which suggests the pre-filter stage is not working
corrosion or deposits appear on compressor blades at inspection
the intake house shows leaks, corrosion or damaged seals
Any of these means the system needs investigation, not just a filter change. A new set of filters in a leaking housing protects nothing. Find the cause, fix it, then fit the filters.
Specifying intake filters for a plant
For a power generation, oil and gas or industrial plant, the specification should start with the turbine model, the original part numbers, the operating environment — coastal, inland, dusty, humid — and the change-out schedule. From those, the stages can be matched: pre-filter, coalescer and high-efficiency final, each to the original part number. Airguard's specification matching service identifies the correct equivalents, and you can request a free estimate for the filters the intake needs. Keep a small stock of the filters the site uses most, and order replacements a full lead time ahead of the planned outage. Power generation filters for coastal sites are specified with the salt load in mind from the start.
Wrapping up
A gas turbine intake filter protects the most expensive machine in the plant from the cheapest threats in the air: dust, salt and water. The protection works as a train — pre-filter, coalescer, high-efficiency final — and it works only if every stage is matched to the original, sealed properly and changed on pressure drop. Get those right and the turbine holds its output. Get them wrong and the turbine pays for it, quietly, every hour it runs.
Further reading
FAQs
What are gas turbine intake filters?
They are the filtration train in the turbine's filter house — pre-filters, coalescer panels and high-efficiency pocket filters — that clean the air before it reaches the compressor, removing dust, salt aerosol and water droplets that would otherwise foul it, corrode blades and cut output.
What is the difference between a gas turbine intake filter and an inlet filter?
There is no technical difference; "intake" and "inlet" are two words for the same system. What matters is the stage: a pre-filter, coalescer or high-efficiency final filter each does a different job, and the specification should name the stage, not just the system.
How often should gas turbine intake filters be changed?
Change on pressure drop, not on the calendar alone. As a starting point, pre-filters last 3 to 6 months, coalescers 6 to 12 months and high-efficiency final filters around 12 months, but coastal, dusty and continuously running sites shorten all three. Log the pressure-drop readings and set the site's intervals from the data.
Can I use OEM-equivalent filters in a gas turbine intake?
Yes, provided the equivalent is a true equivalent: same dimensions, same efficiency class and same media behaviour as the original, verified against the original part number. Airguard supplies Altair equivalent Filters and other OEM-equivalent replacements matched to original part numbers.
Why is salt such a problem for gas turbines?
Salt aerosol passes through coarse filtration and deposits on compressor and turbine blades, where it drives corrosion, including hot corrosion at high temperatures. Coastal and offshore turbines need coalescer stages specifically to capture salt aerosol and drain it away before it reaches the machine.