Airguard Envirocare
All Insights

GE Gas Turbine Inlet Filters: LM6000 Guide

19 November 2026
GE Gas Turbine Inlet Filters: LM6000 Guide

Introduction

The GE LM6000 is one of the most widely installed aeroderivative gas turbines in the world — power generation, oil and gas, industrial plants — and every one of them breathes through an inlet filtration system that decides how long the compressor stays clean. When an LM6000 inlet filter needs replacing, the plant needs a filter that matches the original GE specification exactly: same dimensions, same rating, same behaviour. This guide covers GE gas turbines inlet filters for the LM6000, the verified Airguard equivalent, and how to order the right filter without guessing.

The LM6000 inlet: what the first stage does

The LM6000's inlet filtration starts with a pre-filter stage. Its job is to catch coarse dust and large particles before they reach the finer stages behind it, and to take the bulk of the loading so the expensive final filters live a full life. A pre-filter that is skipped, or left in place too long, passes its load downstream — and the final filters pay for it in shortened life and rising pressure drop.

The pre-filter for the LM6000 is a pleated panel filter, and the specification that matters most is its rating. The verified Airguard equivalent for this duty is built to a G4 rating under EN 779, with a MERV 8 classification — a coarse pre-filter rating that captures the large particulate while keeping resistance low. That balance is the whole point of a pre-filter: stop the big stuff, let the air through, and protect what is behind it.

The verified equivalent: DPGT-AG

Airguard Envirocare's DPGT-AG is a GE-equivalent industrial panel filter for the LM6000 gas turbine, engineered as a G4-rated pre-filter for onshore turbine installations. It is listed on the site's OEM cross-reference with the original part numbers it replaces:

  • GE LM6000 PN: 0423495

  • DPGT-405G, HBD/000619F, HBD/006204F, HBD/006503F

The published specification for the DPGT-AG is:

  • Filter type: Pleated panel, G4 (EN 779), MERV 8, Class 2 (UL900)

  • Airflow: 1,040 – 2,710 CFM (1,770 – 4,600 m³/h) by size

  • Temperature range: −40 to 70 °C

The media is 100% synthetic, pleated and non-shedding, in a moisture-resistant beverage-board double-wall frame with expanded metal support mesh and finger spacers on both faces. It is a disposable pre-filter — designed for disposal at the end of its life, which keeps change-out time short compared with washable filters. It is built to the same G4 rating and dust-holding performance as comparable pleated pre-filters from suppliers such as Parker Hannifin, manufactured in the UK under ISO 9001, and covered by a 12-month manufacturer's warranty. Twenty-three standard models are listed, and bespoke sizes are available where the installed housing is non-standard.

Its final resistance rating is 1.0 inch water gauge at its rated velocity of 625 feet per minute — the figure the change-out decision is built on. When the resistance reaches that point, the filter has done its job and should be changed.

How to match a GE inlet filter

Matching a GE inlet filter follows the same discipline as any OEM equivalent gas turbine intake filter: the part number is the starting point, and the specification is the proof. For the LM6000 inlet, the matching checklist is:

  • Part number: the GE part number on the installed filter — for example GE PN 207D1202P0001 or GE LM6000 PN 0423495 — cross-checked against the OEM cross-reference.

  • Dimensions: the installed filter's face size and depth. The DPGT-AG is built in 12–25 inch nominal sizes with a 592 mm metric build and a 95/89 mm depth; a filter a few millimetres out will not seal, and an unsealed pre-filter is a bypass path.

  • Rating: G4 under EN 779, MERV 8. A replacement of a different class changes what reaches the stages behind it.

  • Airflow: the site's design airflow against the filter's rated range — 1,040 to 2,710 CFM by size for the DPGT-AG.

  • Environment: onshore installation, temperature range, dust loading and humidity. The DPGT-AG is rated from −40 to 70 °C for onshore turbine installations.

Send the part number together with the dimensions, airflow, required efficiency and operating environment, and the engineering team confirms the match. Airguard's specification matching service works from exactly this information, and quote requests are answered within 24 hours.

Pre-filter change-out: timing and practice

A pre-filter's life is set by loading, and loading is set by the site. The change-out decision should be built on the resistance reading: when the filter approaches its final resistance of 1.0 inch water gauge at rated velocity, it is time to change. Calendar intervals are a backstop, not the decision — a dusty site will load a pre-filter far faster than a clean one, and a pre-filter left in place too long passes its load to the final filters behind it.

Change-outs should be done at a planned stop, with the intake isolated so filters are not changed under suction. Inspect the housing while it is empty: clean the tracks, check the gaskets and seals, and look for corrosion or damage. Fit each filter the right way round, check the seal all round the frame, and record the date and the resistance reading. And order replacements ahead of the outage — the standard lead time for made-to-order industrial filters is four weeks, so a change-out delayed because the filters are on order is a change-out that should have been planned.

Beyond the LM6000: what this guide does and does not cover

This guide covers the LM6000 because that is the GE frame with a verified cross-reference on the Airguard site. Other GE frames exist, and other turbine manufacturers — Siemens, Solar and others — have their own inlet specifications and part numbers. Those are not covered here, because no verified cross-reference for them is published on the site, and this guide does not invent compatibility claims. If your turbine is a different GE frame, or a Siemens or Solar machine, send the existing part number and the specification: the engineering team assesses the installed filter and confirms whether a match exists, and what it is. A checked match is worth far more than a fast guess — and a guide that claims a match it cannot prove is worse than no guide at all.

The same discipline applies across the whole intake, and to every OEM range Airguard covers — the verification steps in this guide are the same ones applied to Parker / Altair equivalent Filters, where a large installed base and a mature equivalent range make the part-number check even more important. The gas turbine intake filters guide sets out the full train — pre-filter, coalescer, high-efficiency final — and the LM6000 pre-filter in this guide is the first stage of that train. The final stages matter just as much, and they are matched the same way: part number, dimensions, class, media and pressure drop, in writing, before the order.

Why an equivalent, and why this one

Plants switch to equivalents for three practical reasons: availability, consistency and engineering support. A UK manufacturer answering quotes in 24 hours and building to order removes the single-source queue; the same equivalent, reproduced to the same specification, keeps the intake performing identically across change-outs; and an engineering team that assesses the existing specification — rather than selling a size — keeps the match honest. The DPGT-AG is built to the same G4 rating and dust-holding performance as comparable pleated pre-filters from suppliers like Parker Hannifin, at a lower unit price, without compromising on media quality or construction. That is the standard an equivalent should meet: same performance, verified in writing, from a manufacturer that can prove it.

Wrapping up

GE gas turbine inlet filters for the LM6000 start with the pre-filter, and the pre-filter starts with the part number. The DPGT-AG cross-references GE PN 207D1202P0001 and GE LM6000 PN 0423495, is built to G4/MERV 8 with a published airflow range and a final resistance of 1.0 inch water gauge, and is covered by a 12-month manufacturer's warranty. Match it on part number, dimensions, rating and airflow; change it on resistance; and keep the match on file for the next order. To start, send the GE part number and the specification — and request a free estimate for the filters the inlet needs.

FAQs

What is the Airguard equivalent for the GE LM6000 inlet filter?

The DPGT-AG industrial panel filter. It is listed as an OEM-equivalent filter compatible with the GE LM6000 gas turbine, cross-referencing GE PN 207D1202P0001, GE LM6000 PN 0423495, DPGT-405G and HBD/000619F, HBD/006204F and HBD/006503F.

What rating is the DPGT-AG built to?

It is a G4-rated pleated panel pre-filter under EN 779, with a MERV 8 classification and Class 2 under UL900. The media is 100% synthetic, pleated and non-shedding, in a moisture-resistant double-wall frame.

How do I find the right GE inlet filter for my turbine?

Send the existing GE part number, the filter dimensions, the design airflow, the required efficiency and the operating environment. The engineering team cross-checks the part number against the OEM cross-reference and confirms the match before quoting.

When should an LM6000 pre-filter be changed?

Change on resistance: the DPGT-AG has a final resistance rating of 1.0 inch water gauge at its rated velocity of 625 feet per minute. When the reading approaches that point, the filter has done its job. Calendar intervals are a backstop, not the decision.

Is the DPGT-AG washable?

No. It is a synthetic pleated pre-filter designed for disposal at the end of its life, and it is easily disposable by incineration, which keeps change-out time short compared with washable filters.

References